Mechanical Service Technician ( Injection Molding)

Night shift 6 : 45pm-7 : 15am Core Functions :

• Analyze and resolve root causes for ongoing quality issues as they relate to assembly, mold or molding processes including all other supporting technical processes
• Communicate technical status updates to Supervisor Production / Head of Production Unit & Head of Maintenance
• Provide production planning process based on the customer needs, machine assignment, press and mold availabilities
• Build the technical strength of the team through hands on training

All of the below are part of the responsibilities of this position as needed :

MECHANICAL AND ELECTROMECHANICAL EQUIPMENT

Repair / replace brakes & clutches, gears, belts, sheaves / pulley, chains and sprockets, cams, seals and o-rings, bearings and bushings.

Replace couplings and valves (cut-off, pressure relief, etc).

• Troubleshoot / repair / replace, gears, cams, seals, o-rings, bearings, bushings, shafts and motors.
• Troubleshoot / maintain chains and sprockets. Perform basic alignment.
• Maintain couplings and fans.
• Install / maintain valves (cut-off, pressure relief, etc).

PNEUMATIC / HYDRAULIC EQUIPMENT

• Troubleshoot / repair / replace cylinders and pneumatic / hydraulic motors.
• Maintain hydraulic systems, pumps and valves.
• Repair / replace pneumatic / hydraulic lines, hoses, and solenoids.
• Repair / replace flow controls (pneumatic or hydraulic).
• Troubleshoot / maintain air compressors.

CONVEYING SYSTEMS

Troubleshoot / repair / replace / maintain vibratory, linear motion, and material conveying systems. Repair / replace belt conveyor systems.

PUMPS SYSTEMS AND MECHANICAL EQUIPMENT

• Troubleshoot / maintain centrifugal, vacuum, gear, diaphragm, positive displacement and metering pumps.
• Perform alignment.
• Maintain heat exchanger and pipe insulation systems.

MECHANICAL OPERATIONS

• Perform welding and fabrication tasks, sheet metal fabrication, pipefitting duties and rigging tasks.
• Perform basic math operations.
• Operate common hand and power tools, use measuring devices and precision devices.

ELECTRICAL, POWER DISTRIBUTION AND ELECTROMECHANICAL SYSTEMS

• Apply knowledge of AC theory and run wire and conduit.
• Install / repair basic AC and DC controls, building electrical systems.
• Operate electrical test equipment.
• Fabricate / retrofit electrical control panels.
• Repair ground fault detection systems.
• Repair / replace AC motors, starters and relays.
• Maintain ground fault detection system.

MACHINE AND PROCESS CONTROLS

• Modify ladder logic and edit PLC software.
• Troubleshoot / replace / install circuit boards.
• Install / maintain / troubleshoot photo eyes and basic VFD drives (Variable Frequency Drive).
• Install / maintain / troubleshoot limit and proximity switches & bar code readers.
• Calibrate / install / repair basic flow and density, temperature, pressure transmitters, gages and switches
• Calibrate proportional control valves and process control loop (PID).
• Install / calibrate load cells.
• Troubleshoot / replace transducers.
• Align and replace photo eyes.
• Install load cells.
• Repair / replace VFD drives (Variable Frequency Drive), limit and proximity switches.
• Repair flow, pressure, and speed transmitters, gages and switches.

AUTOMATION

• Troubleshoot / repair / replace / maintain robots.
• Design / FAB / troubleshoot end of arm tooling
• Program pick / place points.

GENERAL

• Setting the example for professionalism in all activities.
• Maintain housekeeping of work area.
• Consult and work with direct manager on all technical issues.
• Notify direct manager of any non-standard or sub-performance operational issues as well as quality and safety issues.
• Ensure safety adherence.
• Ensure that established policies, procedures, rules and regulations are understood and followed.
• Participate in all training programs as well as the GMS

Qualifications Education Requirements :

• High School Diploma
• Requires a minimum of 2 years maintenance / technical experience within an plastic injection molding facility.
• Requires a minimum of 1 year mechanical / electrical experience.
• Requires a minimum of 2 years general preventative maintenance experience in medical injection molding industry.

Experience Requirements :

• Experienced knowledge of Good Manufacturing Practice within the Medical or Food Industry.
• Experience working in a fast paced operational environment with constant interaction with operators, technicians and equipment.
• Experience in problem solving and troubleshooting of processes and process equipment
• Prior diagnostic / troubleshooting and preventative experience preferred.
• Ability to read blue prints, manufacturer's specifications and schematics

Additional Information

• Must have good interpersonal skills with the ability to interface constructively and cooperatively with a wide variety of departmental staff and intra-department personnel.
• Attention to detail and accuracy.
• Ability to work well within a team environment and capable of completing projects with minimal supervision.
• Excellent verbal communication skills.
• Required to speak, read and write English language
• Good organizational and planning skills
• Required to supply hand tools

Pay Details : $32.00 to $36.00 per hour

Equal Opportunity Employer / Veterans / Disabled

To read our Candidate Privacy Information Statement, which explains how we will use your information, please navigate to

https : / / www.adeccousa.com / candidate-privacy

The Company will consider qualified applicants with arrest and conviction records subject to federal contractor requirements and / or security clearance requirements.

Last updated : 2024-05-18