Assembler

Denyo Manufacturing Corporation builds the dependable, quiet and versatile diesel-driven generators for a variety of applications. To maintain and improve the company’s products and reputation, every employee must be focused on completing his/her job in the most timely, efficient and cost-effective manner.

Responsibilities and Duties may include:

Read and understand work instructions

· Read and compare part numbers and identifying markings on wires and terminals

· Route and connect wires from generator to correct terminals on selector switch

· Route and connect wires to terminal board and terminal strip

· Gather and tie generator wires and wires at terminal board

· Use test meter to verify correct dielectric and continuity test readings

· Install covers for selector switch, control box, changeover switch, and 3-phase output terminal

· Install corrugated protective plastic tubing around generator wires

· Re-tap threaded holes

· Install acoustic insulation

· Align and install radiator

· Install radiator drain hose, overflow hose and clamps; tighten clamp securely

· Assemble and install engine fan shroud

· Install upper and lower radiator hoses and clamps; tighten clamps securely

· Install upper and lower intercooler hoses and clamps; tighten clamps securely

· When applicable, operate overhead crane to move radiators and/or sub-assemblies

· Route wires to current transformers and circuit breaker, connect wires to circuit breaker and tighten bolts to specified torque

· Install positive battery cable on battery. Install negative battery cable to battery; install ground cable

· Route and connect engine harness wires to the starter, fuel pump and other locations per instructions

· Route and connect engine harness wires to the alternator and tighten bolts to specified torque

· Assemble doors with latches and ducts and install door hinges on generator unit

· Install completed doors on hinges and adjust for even spacing and clearances

· Install front and rear covers

· Apply sealing rubber gasket to door openings

· Check and verify the quality and accuracy of own work and work done by the tea

· Accurately record data on Assembly Check List

· General housekeeping (sweep floors in work areas, pick up and dispose of paper, etc.)

Qualifications, Skills and Education Requirements

· Read and follow written instructions, pictures and diagrams

· Perform moderately complex, but critical, job tasks

· Work with minimal direct supervision to meet production time/Tact requirements

· Adapt to changes in engine and alternator models and assembly requirements

· Average or better mechanical aptitude and/or work experience involving use of hand and power tools

Load/unload metal parts on paint line

· High school diploma or GED preferred

Physical Requirements

· Must be able to differentiate colors of wires and connectors

· Fine manual dexterity skills for manipulating wires, connectors and hand tools

· Stand or walk eight to ten hours or more on a frequent basis

· Lift 20 pounds or less frequently

Lift 50 pounds or more occasionally

· Bend and/or squat frequently while performing job tasks

· Grasp, push, pull, and manipulate objects frequently with one or both hands

· Use required personal protective equipment (e.g. safety shoes, safety glasses)

* These are representative of the physical requirements necessary for an employee to successfully perform the essential functions of the job. Reasonable accommodation can be made to enable persons with disabilities perform the essential functions

Working conditions

· Normal work schedule is 6:00 a.m. until 4:30 p.m., Monday through Thursday

· Additional, scheduled and required overtime hours are likely, usually on Friday. We will work an occasional Saturday.

· Work space is clean and well-lit, free of dusts and chemical vapors

· Work space is well-ventilated but subject to moderate seasonal variations in temperature

• This job description is intended to summarize information needed to understand the scope of the job and the general nature of work performed by those in the job. However, this job description is not intended to be an exhaustive list of qualifications, skills, duties, responsibilities or working conditions associated with the position.

Job Type: Full-time

Pay: From $16.50 per hour

Benefits:

• 401(k)
• 401(k) matching
• Dental insurance
• Employee assistance program
• Employee discount
• Flexible spending account
• Health insurance
• Life insurance
• Paid time off
• Referral program
• Retirement plan
• Vision insurance

People with a criminal record are encouraged to apply

Work Location: In person

Salary : $17