Electrical Engineer

We are seeking a hands-on Electrical Hardware Engineer to own end to end development of electrical subsystems for next generation digital radiographic equipment and mobile medical platforms. In this role, you will lead designs from concept through production, with a focus on power electronics (including high voltage), battery systems, PCB and harness design, and system integration. You’ll collaborate closely with mechanical, firmware, manufacturing, and supplier partners to deliver robust, manufacturable designs that meet performance, safety, and regulatory expectations.

Position Responsibilities

:• Troubleshoot and diagnose a broad range of electrical issues in both released products and in development hardware; perform root cause analysis and corrective actions

.• Own electrical subsystems through development cycle from requirements, schematic capture, PCB design/layout oversight, cabling/harnessing, component selection, documentation with support of QA V&V and production release activities

.• Design and guide high speed PCB layouts in Altium Designer; drive stack up, impedance control, SI/PI considerations, and EMI/EMC best practices

.• Design harnesses (conventional wire and flex), including connector/terminal selection, wire gauge/safety considerations, strain relief, and documentation

.• Develop power electronics architectures (including high voltage, power generation and distribution, grounding, protection, and safety) suitable for mobile and medical environments

.• Prototype and integrate new designs at the system level; support bring up, test fixture development, and verification/validation activities

.• Collaborate with suppliers/Commodity Managers on fabrication, test, DFM/DFT feedback, first articles, and component obsolescence mitigation; resolve build and test issues swiftly

.• Generate clear design documentation (requirements, specifications, drawings, BOMs, etc. ) ensuring traceability and compliance

.• Contribute to system architecture, including new data path concepts for imaging systems; participate in IP development and review as appropriate

.
Required Skills & Educatio

n:• Bachelor’s degree in Electrical Engineering, Electronics Engineering, or Computer Engineerin

g.• 7 years of hands on electrical engineering experience, serving as the technical lead for the electrical systems on 3–5 products from concept through productio

n.• Strong power electronics experience, including high voltage design, power generation/distribution, grounding, protection, and safety (preferably in mobile and medical environments

.)• End to end subsystem ownership: schematic capture, PCB design/layout oversight, cabling/harnessing, component selection, documentation and support of QA V&V and production release activitie

s.• Practical prototyping experience with hands on fabrication and assembly of prototype PCBs, wiring harnesses, and test fixtures to support feasibility evaluation

s.• Design for Manufacturing (DFM)/productization experience including PCB layout trade offs, electro mechanical integration, tolerance stack up awareness, and collaboration with contract manufacturers and supplier

s.• Strong analytical troubleshooting and problem solving skills using lab equipment (oscilloscopes, logic analyzers, electronic loads, etc.); ability to isolate board level issues to component leve

l.• Wire harness design and documentation experience, including connectors, terminals, wire gauge selection, and heat shrink/strain relief practice

s.• Battery system experience with Lead Acid and Lithium ion, with knowledge of emerging chemistries; strong understanding of BMS hardware and charging system

s.• Experience implementing designs under regulatory guidelin

es• System level thinking: capable of balancing size, weight, power, and thermal constraints while collaborating across mechanical, firmware, and manufacturing team

s.
Desired Skil

ls:• Proficiency in PCB Layout (schematic capture and guiding PCB layout) for new product development, preferably with Altium Design

er.• Knowledge of general radiography and fluoroscopy—theory of operation and key system componen

ts.• Familiarity with safety standards IEC 60601 2 54 (X ray equipment for radiography and radioscopy) and IEC 60601 2 43 (X ray equipment for interventional procedure

s).• Background in motion control, including selection and integration of stepper, servo, or BLDC motors; experience with motor driver circuits; encoder feedback; and closed loop control for precise motion/positioni

ng.• Working knowledge of Microsoft Visio for Electrical drawings and documentati

on.• Practical soldering skills down to 0402 package size (rework and prototype build

s).• Familiarity with wireless technologies (e.g., Bluetooth, Wi Fi) as applied to embedded/medical syste

ms.
Work Environment: Rochester Office, Lab, and

Home
• Physical Requirem

ents:
o Standing:

1-25%o Walking:

1-25%o Sitting:

51-75%o Bending:

1-25%o Lifting up to 20 pounds:

1-25%o Lifting 20-35 pounds:

1-25%o Carrying, Pushing or Pulling:

1-25%
•

Travel:o Domestic and international travel to supplier and customer sites may be re

quired.o 1-2 weeks a